This guide explains how the cooling circuits on an HFO plant are arranged, the choice between radiators and cooling towers, and the design points that matter most on hot, dusty mine sites and on utility stations that run around the clock.
Where the heat comes from
A medium-speed engine has several heat sources that need cooling: the cylinder jackets and heads, the charge air after the turbocharger, the lubricating oil and, on some designs, the fuel injectors. These are grouped into a high temperature circuit, mainly for the jackets and the first stage of charge air cooling, and a low temperature circuit for the second charge air stage and the oil cooler.
Keeping these temperatures within the engine maker’s band is not only about preventing overheating. Charge air that is too warm reduces output and raises exhaust temperature; jacket water that is too cool can cause acid condensation from the sulphur in heavy fuel. Good design holds both circuits steady across the full load and ambient range. Our overview of how an HFO plant works places these circuits in the wider plant.
Radiators or cooling towers
Most engine plants at mines and in water-scarce regions use closed-loop radiators. Fans blow ambient air across finned coils, and the engine water never contacts the air. They use almost no water, which matters where every cubic metre must be pumped from boreholes or competes with the process plant.
Cooling towers with a heat exchanger can achieve lower water temperatures in hot weather, which may help output, but they consume water through evaporation and blowdown and need chemical treatment. On most remote mine sites, radiators win. Some utility plants near a reliable water source choose towers, and some use a hybrid arrangement where wetted pads or misting assist radiators only on the hottest days.
Designing for hot ambient and altitude
Radiators are sized for a design air temperature. If that figure is taken from an average day rather than the hottest likely afternoon, the engines will derate when the plant is most stretched. Use local climate data and add a margin for the warm air that recirculates around a crowded radiator field.
Altitude reduces air density, so each radiator moves less mass of air and rejects less heat. Engine output also falls. A plant on a highland mine therefore needs both more radiator area per megawatt and possibly more engines than the same plant at the coast.
Layout of the radiator field
Radiators work best with a clear path for cool air in and warm air out. Banks placed too close to the engine hall, other buildings or each other can draw in their own hot exhaust air. Mount them high enough for good air flow beneath, and orient the field so the prevailing wind carries warm air away rather than back over the coils.
Keep engine exhaust stacks well clear of radiator intakes. Hot, oily exhaust drawn into the coils raises inlet temperature and fouls the fins. These points are easy to fix on the layout drawing and expensive to fix after construction.
Dust, insects and fouling
Mine sites are dusty, and radiators act as large air filters. Dirt on the fins reduces heat transfer and raises water temperature month by month. Plan regular cleaning with low-pressure water or air, design walkways and access so the work is safe, and consider coarse screens on the intake side in very dusty areas.
Track the approach temperature, the difference between water outlet and ambient air, at similar loads. A steady rise is the earliest sign that cleaning is due and is a better trigger than a fixed calendar.
Water quality inside the circuits
Closed cooling circuits still need treated water. Untreated or hard water causes scale on liners and coolers, while poor inhibitor levels lead to corrosion and cavitation damage on cylinder liners. Fill with demineralised or softened water, dose a suitable inhibitor and test it regularly.
Coolant condition and lube oil condition are linked, because a leaking oil cooler or liner seal shows up in both. Our post on lube oil management for HFO engines explains how oil analysis can reveal cooling water ingress early.
Redundancy and future units
Each engine usually has its own radiator set, so a fan or coil fault affects only one unit. Within each set, several fans share the load and the system should still hold temperature with one fan out of service. Fan motors and drives should be easy to reach and replace without stopping the engine.
When the plant is designed for later expansion, reserve space for the extra radiator banks with the same clear air paths as the first ones. Squeezing new radiators into a crowded field is one of the most common reasons expanded plants run hotter than the original design.
Upgrading cooling on an existing plant
Older plants that now derate every summer can often be improved without new engines. Options include replacing fouled or corroded radiator cores, fitting higher capacity fans, raising radiators to improve air flow, or moving banks away from exhaust plumes. Each change should be checked against measured approach temperatures so the gain is proven rather than assumed.
These upgrades are frequently combined with engine and alternator work during a major outage, as part of a broader plant refurbishment programme.
Operations checks that protect output
Operators should log high and low temperature circuit temperatures, charge air temperature, fan status and approach temperature each shift, together with engine load. Trends across weeks show fouling, failing fans or thermostat problems before they cause a derate.
On mine stations with tight availability targets, cooling faults are a frequent cause of lost megawatt-hours in summer. Our post on availability at mine HFO plants shows how these losses can be tracked alongside engine faults.
About the authors
This guide comes from the USP&E HFO plant mechanical engineering team. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Full station delivery is described in our guide to HFO station EPC and O&M.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
HFO plant cooling questions
How are HFO power plant engines cooled?
Usually through high and low temperature water circuits that cool the jackets, charge air and lube oil, with the heat rejected to air through radiator banks or to water through a cooling tower.
Are radiators or cooling towers better for a mine HFO plant?
Radiators suit most mine sites because they use almost no water. Cooling towers can give cooler water in hot weather but consume water and need treatment.
Why do HFO engines derate on hot days?
Hotter air reduces radiator capacity and raises charge air temperature. If radiators were sized for an average day rather than the hottest likely day, engines must reduce load to stay within limits.
How often should radiators be cleaned?
Base it on the approach temperature trend rather than the calendar. On dusty mine sites that may mean frequent cleaning in the dry season.
Does altitude affect cooling design?
Yes. Thinner air carries less heat, so a high-altitude plant needs more radiator area per megawatt as well as allowing for lower engine output.
Review your plant’s cooling design
Send the site climate data, altitude, engine model and current temperature logs, and our engineers will check radiator capacity and suggest layout or maintenance changes.
You can reach the engineering desk on +27 10 822 2324, send drawings or data sheets to info@uspeglobal.com, or leave the details on the HFO plant enquiry form. Engines and generating sets available for HFO stations are shown on our inventory page.