This guide explains the main technical requirements, the studies the utility will ask for, how protection settings must be coordinated, and what compliance testing at commissioning looks like for a medium-speed engine plant.
What the grid code is for
A grid code sets the minimum technical behaviour every generator must show so that the system stays stable. On smaller national grids, where one HFO plant may supply a large share of demand, the rules are often stricter than on large interconnected systems, because each generator matters more when something goes wrong.
Read the applicable code and the utility’s connection conditions before engine selection. Requirements on reactive capability or fault ride-through can affect generator size, excitation system design and transformer specification.
Frequency range and response
Generators must stay connected across a defined frequency band for stated times, and trip only outside it. Within the band, the code usually requires a droop response, commonly in the region of 4 to 5 percent, so that output rises when frequency falls and drops when it rises.
Medium-speed engines respond well to frequency events, which is one reason utilities like them, but the governor settings, load ramp limits and any minimum load must be tuned together. A plant that responds quickly but then trips on an engine limit makes the disturbance worse.
Voltage and reactive power
Most codes require the plant to supply or absorb reactive power across a range of power factors at the connection point, often specified as a capability chart, and to hold voltage within a set band. That capability must be provided at the grid side, after the step-up transformer, which means generator rating and transformer tap range both matter.
The automatic voltage regulator should support voltage control and power factor control modes, with settings agreed with the system operator. Limits for under and over excitation must be coordinated with protection so the regulator acts before a trip occurs.
Staying connected through faults
Fault ride-through rules define a voltage against time profile. When a fault elsewhere on the network pulls voltage down, the plant must remain connected while voltage stays above that curve. Large synchronous generators driven by engines contribute useful fault current and inertia, but they can lose synchronism if a fault lasts too long or the network is weak.
Transient stability studies show how close the plant comes to pole slipping for the faults and clearing times in the code. Results may call for a faster excitation system, a power system stabiliser, or a request to the utility to confirm shorter protection clearing times on nearby lines.
Generator protection and coordination
Generator protection typically includes differential, loss of excitation, reverse power, negative phase sequence, over and under voltage and frequency, and back-up overcurrent. The grid code limits how sensitive some of these may be, because a generator that trips for a distant disturbance takes support away when the system needs it most.
Loss of mains functions such as rate of change of frequency and vector shift deserve special attention. Settings chosen for an embedded plant can trip a utility-scale plant unnecessarily. Protection studies should be shared with the utility and settings signed off by both sides. Our article on HFO plants for utilities and IPPs covers the commercial side of these obligations.
Power quality
Engine-driven synchronous generators produce little harmonic distortion themselves, but auxiliary drives, rectifiers and any battery systems on site can. The code sets limits on harmonics, flicker and voltage unbalance at the connection point, and the plant must show it stays within them in all normal configurations.
Flicker can arise when large auxiliaries start or when engines operate with uneven combustion. Clean commissioning of fuel systems and balanced cylinders help here as much as electrical design.
Studies the utility will ask for
Expect load flow, short circuit, transient stability and protection coordination studies, plus validated dynamic models of the engines, governors, generators and excitation systems in the utility’s simulation format. Models must match the equipment actually delivered, so data from the engine and generator makers should be requested early.
Where the plant shares a substation with a mine or industrial load, the studies must include that load, because large motor starts and process trips appear to the grid as disturbances from the generator side. The modelling of engine behaviour draws on the duty profile explained in our page on medium-speed generator duty.
Compliance testing at commissioning
Before commercial operation, the plant demonstrates its behaviour in front of the system operator. Typical tests include voltage regulator step responses, reactive capability at several load points, governor response to simulated frequency steps, ramp rate checks and confirmation of protection settings.
Test results are compared with the dynamic models, and the models are updated if behaviour differs. Our HFO station EPC and O&M guide shows where these tests sit in the commissioning sequence.
Keeping compliance for the life of the plant
Compliance is not a one-time event. Replacing an excitation system, adding engines, changing governor software or uprating a transformer can change plant behaviour, and most codes require the utility to be told and some tests repeated.
Telemetry and dispatch interfaces also need care. Set point signals, status indications and metering must remain reliable, because a plant that ignores dispatch instructions through a failed link can be treated as non-compliant even if its machines are healthy.
About the authors
This guide comes from the USP&E electrical engineers and commissioning leads who connect HFO plants to utility networks and run them under grid code obligations. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Grid studies and connection works form part of our power plant EPC projects.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Grid code questions
What is a grid code?
A set of technical rules every generator connected to a network must meet, covering frequency, voltage, reactive power, fault behaviour, protection and power quality.
Do HFO engine plants need fault ride-through?
Yes, where the code requires it. The plant must stay connected while voltage stays above the code’s voltage against time curve during network faults.
What droop setting is typical for frequency response?
Many codes call for droop in the region of 4 to 5 percent, but the exact value is set by the applicable code and the system operator.
Which studies are needed for a grid connection?
Load flow, short circuit, transient stability and protection coordination studies, plus validated dynamic models of engines, governors, generators and excitation.
What is tested at grid code compliance testing?
Voltage regulator steps, reactive capability, governor response to frequency steps, ramp rates and protection settings, witnessed by the system operator.
Does compliance need to be repeated after changes?
Often yes. New excitation systems, extra engines or control software changes usually require notifying the utility and repeating some tests.
Prepare your plant for grid connection
Send the connection agreement, grid code version and single line diagram, and our engineers will map the studies, settings and tests your HFO plant needs.
You can reach the engineering desk on +27 10 822 2324, send drawings or data sheets to info@uspeglobal.com, or leave the details on the engineering contact form. HFO engines and generator sets are listed in our equipment stock list.